Showing posts with label Free-mo. Show all posts
Showing posts with label Free-mo. Show all posts

No Duck Mo V2.1

In August 2021 I posted my plans for a Free-mo lift gate that I called No Duck Mo V2.0.

In the fall of 2024 a dedicated model railroader in Chilliwack, British Columbia began building two of these using my 2021 plans. He has made very good progress. There were a couple of small errors in my plans for V2.0 that he pointed out to me so I have updated the plans and named them No Duck Mo V2.1.

Here is a link to download the plans:

No Duck Mo V2.1

Animation - Part 2 - Design

I decided to take on the challenge of creating my own track system to create animation. You will note that this uses the concepts used by the Magnorail system referred to in Part 1 but is not an attempt to replicate the Magnorail system. As I don't have access to any Magnorail parts I designed my own parts, several of which appear to be quite different. I also don't know the dimensions of any of the Magnorail parts so I came up with my own dimensions.

I ordered a high-torque 12 volt DC motor from Amazon. The output shaft turns at 5 RPM. I then designed and 3D printed a drive mechanism to sit on top of the motor. Here are pictures of the drive mechanism:

motor mounted to underside of drive mechanism

top side view

with drive gears mounted (note hole the closest gear fits over the "D" gear shaft so it doesn't slip)

same as above but with retainers pressed into holes

Next I created 3D printed chain components which connect to each other and which have holes to fit round rare-earth magnets in a couple of places to move boats:


The track components look like this - each track piece is screwed to a sub-floor which which will reside underneath the styrene sheet "pond":



Here is a picture of the completed track, with the drive mechanism in place:


Here is a picture of the subfloor mounted underneath the pond cutout in the Free-mo module:

The subfloor is mounted with wingnuts to make it easy to remove the subfloor with the track in case adjustments or repairs are ever needed in the future. The motor is wired to a bridge rectifier which takes DCC current from the accessory buss running under the Free-mo module.

Here is a top-side view of the styrene sheet. The beaver dam will be built to disguise the front edge:


Here is a short video showing the boat moving (the rough brown circle painted on the surface is where the beaver lodge will be built):



I will not be sharing the design details or the STL 3D printer files, either for no cost or for a price

Next up......doing the scenery.

No Duck Mo V2.0

In January 2019 I began a seven-part series describing a Free-mo module that incorporated a liftgate so a person could walk through a Free-mo setup without having to use a traditional "duck under" for doing so. I called it my "No Duck Mo", with "Mo" referring to the fact that it is a module.

In October 2020 I began a four-part series describing a two-level lift gate which I designed and built for my basement layout. I came up with several design improvements in working through the mechanics for this liftgate.

At Free-mo events, I am often asked whether I would be willing to share my plans for the No Duck Mo. My response has always been that I would be delighted to share my plans except my approach has always been to design something in my head, perhaps with a few very rough pencil sketches, but most of my design work is done on the fly.

In February 2021 I was contacted by a member of the Calgary Free-mo group, Jim I. Jim was asking about my plans to which I answered that there are no plans but since the start of COVID-19 I had in the back of my mind the thought that an excellent COVID project would be to design and built No Duck Mo V2.0 and create detailed instructions as I did. I told Jim to give me six weeks to get this started. This took me a bit longer, almost two months, because the documentation took longer than the design and construction.

Following are links to the detailed instructions as well as two files which include step-by-step instructions for assembling and for taking apart and packing No Duck Mo V2.0. The information in the latter two files is found at the end of the "complete detailed instructions" but I reproduced these as separate files so copies could easily be printed separately.


No Duck Mo V2.0 complete detailed instructions

No Duck Mo V2.0 setup instructions alone

No Duck Mo V2.0 take down instructions alone

Automated Signals for Free-mo (Infrared Detection) - Part 3 of 3

Here is the wiring to take the signals from the infrared sensors under each track and also to power the dual signal heads:



I am pleased to report that the system works as designed. Here is a shot of the signal masts:


These masts are mounted on one of the Free-mo modules in my basement layout. I have yet to build any individual dedicated Signal-mos. Once I have done so I shall post pictures.

Automated Signals for Free-mo (Infrared Detection) - Part 2 of 3

 Other components of my signalling system include:

Signal Masts

As with my last signal project described in December, I again made my own signal masts using the same jig described at that time. However, as can be seen in the above picture each mast is double-headed to accommodate signalling in both directions (in my earlier project I used two separate single-headed masts to control traffic in each direction). Since this project is signalling for double-track Free-mo mainline I need signals for both directions for each track so double-headed signals made for less complexity.

Unlike my earlier signalling project for which the signal masts are permanently mounted on the layout, for the Free-mo signals, I wanted a method of making the signal masts removable so they can be stored and transported separately from the Signal-mo modules to lessen the chance of damage.

In the above picture, the grey-coloured base was 3D printed with snug-fitting mounts on which the signal towers fit. The box with the green, yellow and red stripes fits over the signal masts and is fastened shut with Velcro.

Signal Mast Mounts


The grey component is 3D printed to accept a 10-pin female receptacle.



The above picture shows the receptacle mounted in a module. It is fastened with screws from the underside. The bottom of each signal mast has a 3D printed base in which is mounted a male 10-pin connector which plugs into this female base.


Here is a signal mast mounted on the base.

The 10-pin connectors at the bottom of each signal mast are wired as follows:


The red, yellow and green connectors on the left are wired to the three corresponding colour LEDs facing one direction. The other red, yellow and green connectors are wired to the LEDs facing the other direction. The two white connectors are wired to the shaft of the signal mast which is made of brass. The anodes of all the LEDs are wired to the mast. It is important to note that different colours of LEDs draw different amounts of current. Therefore, in order to ensure a comparable brightness of all LEDs I did a bit of experimentation and wired different strength resistors in the wires to each of the different colour LEDs.

The wiring configuration described above means that it doesn't matter which way around a signal mast is mounted - the same contacts will light the same LED colours regardless of which way around the signal mast is mounted.

IR Detector Mounting

My last blog post described the infrared detectors that are to be mounted between the rails. These need to be mounted in place.


The two receptacles for the signal masts are made to fit in a 3/4 inch hole. The holes between the rails for the IR sensors were made using the high-speed hole saw pictured above.


I 3D printed the above fixture which is used to hold the IR sensors in place from beneath the module.


The picture above shows the two signal tower receptacles mounted under the module on the extreme left and the right of the picture and the two IR sensors mounted in the middle. The wires at the bottom of the picture have nothing to do with this project.


I put a thin layer of Flex Paste around the IR emitter and sensor. Flex Paste is one of the "Flex Family of Products" advertised by that very annoying man on TV. What I like about it for this application is, by soaking a Q-tip in isopropyl alcohol one can easily remove excess material and smooth the leftover surface.


This shows all components mounted in the module. I still need to add some ballast to cover the white Flex Paste. When this picture was taken the IR emitter was powered up - you can tell because a digital camera is sensitive to infrared light (tip - if you want to see the infrared signals coming from any such emitter, such as a TV remote control, simply turn on the camera in your smartphone and point it at the output window of the remote and active the remote control button - very handy if you aren't sure whether the remote isn't working only because of a dead battery or because you dropped and broke it!).

Automated Signals for Free-mo (Infrared Detection) - Part 1 of 3

Happy New Year! I don't think I have ever felt so good about the start of a new year as I feel now.

In December I posted a two-part article that described the design and construction of my automated signalling system which used block detection to identify the presence of a train. The system continues to work flawlessly.

In earlier posts, I have mentioned my participation in Free-mo (see January 27, 2019 post which explains Free-mo model railroading and March 21, 2020 post which explains that the middle level of my home layout consists of Free-mo modules). I have seen working signalling systems on a Free-mo set up at the Big Valley Alberta event which is hosted by the Calgary Free-mo group and where I found that the added realism makes for a good experience.

I decided that it would be impractical to employ block detection to signalling for Free-mo for the following reasons:

  • Free-mo modules are designed and constructed by various people. Modules can be short (say 2 metres) or long (say 30 metres, in multiple sections). In my experience, most are 2 to 4 metres in length. While the Free-mo standard must be followed for the main buss wiring, this does not mean that the wiring to a module has been designed in such a way that a detection circuit could be installed easily without redoing a lot of the wiring. If a person is reluctant to redo their wiring then the signalling system would be frustrated by one module being "dark".
  • Even if a local group of Free-mo modellers agreed to make the necessary modifications to all of their modules to accommodate block detection, one of the benefits of Free-mo is for people with Free-mo modules from other locations to be able to join the group. Since their modules would not have been modified, their modules would be "dark" for signalling purposes.
  • The design of my block detection signalling system placed signal masts at each end of a block. Say if one were to go to the trouble of rewiring all Free-mo modules for a local group there would need to be added a huge number of wires under each module (with an equal number of reliable connections between module sections) to mount signal masts at the end of each module. The wiring of Free-mo is extensive enough without adding many more wires to the mix. This point only refers to the wiring under each module - also, there would need to be wiring to allow the system to communicate the presence of trains to each adjacent module which adds even more wiring.
I decided that the more practical approach would be to make use of dedicated signal modules "signal-mos" on which the signal masts would be mounted. Each signal-mo would be one foot long and would conform with the "mini-mo" supplemental standard published by Free-mo.org. A mini-mo can be narrower than the normal Free-mo standard but I decided that a layout would look better if the signal-mo is the same width as the adjacent modules. Since the signal-mos would be used on mainline track this means a 26-inch signal-mo width and double track.

All wiring related to the signals would be mounted underneath the signal-mo. The only wiring leading from a signal-mo would be a 6-conductor flat "telephone-style" cable connecting the signal-mo with each adjacent signal-mo. Aside from the normal buss wiring for all Free-mo modules, there would be no other connections to adjacent modules.

The presence of trains would be detected with the use of an infrared detection device which looks like this one which I purchased from eBay:


In this photograph, the device is sitting atop the smallest-size Post-in-Note pad to show scale. One of these would be mounted underneath the centre of each track on each signal-mo. The trim-pot which has an X-shape is used to adjust the sensitivity of the infrared detection. One of the "LED" devices on the left is an infrared light emitter and the other is an infrared light detector. When a train passes over the sensor some of the infrared light bounces off the underside and is detected. The three electrical leads consist of positive and negative leads (5 volts DC) and VCC to which is attached a wire leading to an Arduino mounted underneath the track. One Arduino is required for each of the two tracks. The ground wire is also common with the Arduino.

How the Signals will Operate

The following depicts how the system works without showing any of the electronics or wiring:



Some key points:
  • Two-track mainline; the trains are travelling in the same direction that seems to be conventional "normal" travel when there is a double-track mainline (perhaps those in the UK, Australia, Japan, etc. follow a different practice because they drive their cars on the other side of the road from those of us in North America, Europe, etc.).
  • The rails coloured white for each signal-mo (each of these would be 1 foot long and 26 inches wide). The rails coloured grey depict all other Free-mo modules (anywhere from 1 foot to infinity in length and 26 inches wide at module ends).
  • When the train on the lower track passed over the last signal-mo, the IR sensor mounted under the track triggered the backward-facing signal to show red, protecting the train travelling in the module to the right. This same signal-mo tells the adjacent signal-mo to the left of the occupancy so that signal turns yellow as a warning to approaching trains and the requirement to slow down.
  • The engineer of the train on the lower track sees a green signal because both the next module to the right and the one after that are unoccupied.
  • The same principles apply to the other track and also work the same way if the trains were to be operated in the opposite direction.
What a Signal-mo consists of:


Wiring

The following diagram depicts the wiring mounted underneath each signal-mo:


To wire this under each person's individual module along with all of the other wiring and hardware that is under there would quickly become a nightmare.

The following diagram shows the signal-mo with the 6-conductor flat telephone style wires that take signals to adjacent signal-mos:


Complete Picture

Finally, here is a diagram of the complete picture with only one of the signal-mos showing its wiring:


 
Coming up - my next post will explain the construction and assembly of the various "real-life" components.


Ballasting turnouts or tight spots

In my last post, I promoted an idea for avoiding track cleaning by Joe Fugate, publisher of Model Railroad Hobbyist Magazine. Another idea of Joe's that I have found extremely useful pertains to applying ballast around turnouts, in particular around the moveable points. In this area, it is critical that no adhesive or ballast gets in between the moving parts.

The solution is to apply full-strength adhesive between the ties using a micro-brush. In this way the adhesive goes where you want it and not where it would go if it was watered down in the way ballast cement is applied on the rest of the track. Once the adhesive is in place simply scatter ballast on top and leave it to dry. Once dry, vacuum away the loose ballast and you will be left with ballast in only the places you wanted it and not stuck to the moving parts. Ballast can then be added to the track either side of this area, wet with isopropyl alcohol or "wet water" (water with a few drops of dish detergent to reduce surface tension) followed by a diluted mix of your favourite ballast adhesive.

Here are pictures showing the technique:





This technique is also useful around holes left around feeder-wires. Apply the glue and ballast in these areas so that the more watery mixture of ballast adhesive applied later on will not result in adhesive dripping through to the underside of the layout. It also works well on the track at the ends of Free-mo modules where you have installed PC board end tie plates milled into the shape of railroad ties. This technique prevents ballast from sticking to those places where you don't want it.

Completed tourist excursion railway Free-mo module - Part 3 of 3

My post of June 21, 2020, described the completion of the last structure on my new tourist excursion railway Free-mo module. I am pleased to report that all scenery including static grass, parking lot, gravel paths, signage, fencing, trees and people have been added.

The trees are all deciduous and are made from Saskatchewan sagebrush harvested in roadside ditches a couple of hours south of Regina. The sagebrush was sprayed with Raid to kill any bugs and left in a container for a couple of months because I wasn't yet ready to build trees. I then trimmed away excess material and put the future tree armatures on a couple of cookie sheets in the oven at 200 degrees Fahrenheit for 90 minutes to make sure I wasn't bringing any hitchhiking organisms into the house. I attached Supertrees branches with tacky glue and then spraypainted the trunks and branches with light dustings of various shades of matte colour, ranging from grey to black to tan with grey being the predominant colour. I then sprayed the branches with unscented hair spray and sprinkled on various shades of Scenic Express green leaf material. In nature, there are significant variations in colour and shape between trees which is what I was trying to capture.

Here are a few pictures:












Hard wiring burning building

In July 2019 I posted two entries dealing with the concept and construction of a working burning building for my first Free-mo module. The "smoke" comes from a portable desktop humidifier designed to run on 5 volts DC from a USB port. Here is a picture of the building from the July 2019 post:


A picture of the building on the module:

As I explained in the July 2019 posts, contained inside the building is a small rechargeable power supply of the kind that is designed to provide power to a cell phone when a charger can't be used. This works fine but it becomes a nuisance having to switch out the rechargeable power supply when it runs out after 4 hours, give or take.

Some time ago I built a supply of circuit boards for our train club designed to convert 16 volt AC power (the Free-mo standard for the accessory power bus which runs under the Free-mo modules) to various DC voltages which are used by a variety of model railroad accessories, such as building lighting or other animation. I use a Digitrax booster to power this bus because it has very robust short-circuit protection, preventing damage to devices or to the power supply itself in the event of a wiring mistake. A Digitrax booster set to HO scale actually produces 18 volts AC but the device still works fine. Here is a picture of my device:

AC power is fed into the 2-position terminal strip on the left. When power is applied the blue LED glows to show that the power is on. The AC power feeds the bridge rectifier which is at the back of the circuit board from the perspective of the viewer. The bridge rectifier sends 12 volt DC power to four voltage regulators which produce 12, 9, 5 and 3 volts DC power, respectively. The 6-position terminal block contains outputs for ground and these various voltages.

Each of the devices is attached to a heat sink to help reduce the chance of them overheating.

I tried hooking the burning building humidifier to the 5 volt and ground terminals and it works like a charm. I no longer need to have to fuss with the rechargeable power supply.

Free-mo module turnout control

Among the standards required when constructing a Free-mo module are the following:

S4.10 All turnout frogs shall be powered. Turnouts shall not rely on switch points to power the frog.

S5.2 For a given turnout, turnout controls must be on all sides of the module or module section, excepting any endplates.

RP5.2.1 Turnout controls should be located on the fascia, and not on the horizontal or vertical surfaces of your scenery.

On my first-ever module I violated both S5.2 and RP5.2.1 in that I used Caboose Hobbies ground throws which are typically mounted on the horizontal surface of the module, immediately beside the switch points of the turnout. This approach was simple and works fine.

I have decided that I should follow the standards for all subsequent modules not only because the "hand of God" coming down among the scenery and rolling stock can lead to damage to scenery or derailment of rolling stock but also because it isn't very prototypical.

I decided on BullFrog Manual Turnout Control components from FastTracks. These are easy to assemble and are available with an adapter kit which allows for the turnouts to be operated on both sides of a Free-mo module. In addition, provision is made so the frog can be powered, in compliance with S4.10 above (which is a practice that is highly recommended for more reliable electrical contact, regardless of the standard).


At each end of the control rod, the casing of which is shown in red above, there is mounted a wooden disk that serves as the knob used to push or pull the switch points to the desired position. I designed boxes that could be mounted from behind the Free-mo module fascia, with the outer edge flush with the side. I printed these with my 3D printer using black PLA plastic filament so the box would blend in with the black fascia colour.

These are three of the 3D printed boxes shown just before being mounted from behind the fascia. The two on the left are mounted above one another in the same opening because they operate turnouts located very close to one another.



Here you can see the black boxes mounted on each side of module, with the control cables encased in red leading to the Bullfrogs under the turnouts.


The lighting could have been better when I took this picture, however aside from the round disk knob (pained grey) everything else in the picture is black so it is hard to get good contrast. The knob on the right is pulled out while the one on the left is pushed in.